Listing of FC1000III GN6 Parameters
| Parameter | Setting |
Value |
Explanation |
| 0000 | 00100011 | bit 5 | = 1 metric/inch option |
| = 0 metric only | |||
| 0001 | 00001000 | ||
| 0002 | 00100001 | ||
| 0003 | 10011010 | bit 4 | = 1 runtime clock displayed. |
| = 0 runtime clock not displayed. | |||
| Note: Clock data in parameters 57, 58, 59 - clock data clears if machine on less than 6 minutes. | |||
| bit 7 | = 1 P.C. parameters displayed. | ||
| = 0 P.C. parameters not displayed. | |||
| 0004 | 00000000 | ||
| 0005 | 00000010 | bit 1 | = 1 enables C axes. |
| 0006 | 10110001 | bit 5 | = 0 ignore servo off signal. |
| = 1 recognizes servo off signal. | |||
| bit 6 | = 0 normal handling of M30 code. | ||
| 0007 | 11110010 | bit 7 | = 0 automatic drift compensation off. |
| bit 5 | = 1 reference point return uses special G codes. | ||
| 0008 | 00001001 | bit 3 | = 0 powers up in G91 mode |
| = 1 powers up in G90 mode | |||
| bit 7 | = 0 LF CR CR codes are punched as EOB in ISO code | ||
| = 1 LF codes are punched as EOB in ISO code | |||
| 0009 | 00000000 | ||
| 0010 | 00000010 | ||
| 0011 | 01000000 | bit 5 | = 0 decelerate when limit switch opens. |
| = 1 decelerate when limit switch closes. | |||
| 0012 | 00000100 | bits 4-7 | determine that reference counter uses grid method |
| 0013 | 00010000 | ||
| 0014 | 00010001 | X axis DMR (detect multiplying ratio - limit 10,000 counts) | |
| 0015 | 00010001 | Y axis DMR (detect multiplying ratio - limit 10,000 counts) | |
| 0016 | 01110111 | T axis DMR (detect multiplying ratio - limit 10,000 counts) | |
| 0017 | 01110011 | C axis DMR (detect multiplying ratio - limit 10,000 counts) | |
| 0018 | 00000011 | ||
| 0019 | 00010000 | sets time to respond to M code | |
| 0020 | 00001111 | C axis related | |
| 0021 | 00011011 | ||
| 0022-0023 | 00000000 | ||
| 0024 | 00000000 | bit 4 | = 0 mass editing using 0-9999 is enabled |
| 0025 | 00000000 | ||
| 0026 | 00010000 | ||
| 0027 | 4 | X axis CMR (command multiplying ratio) | |
| 0028 | 4 | Y axis CMR (command multiplying ratio) | |
| 0029 | 2 | T axis CMR (command multiplying ratio) | |
| 0030 | 20 | C axis CMR (command multiplying ratio) | |
| 0031-0034 | 0 | ||
| 0036-0056 | 00000000 | ||
| 0057 | ----- | runtime clock - hours | |
| 0058 | ----- | runtime clock - minutes | |
| 0059 | ----- | runtime clock - seconds | |
| Note#1: Param. 3.4 permits display of clock | |||
| Note#2: Reading clears if machine not on a minimum of 6 minutes | |||
| 0060 | 0 | clutch off timer for nibble (TPF 10) | |
| 0061 | 0 | clutch on signal off time (*PE to PFB) | |
| 0062 | 0 | ||
| 0063-0064 | 00000000 | ||
| 0065-0069 | 0 | ||
| 0070 | 100 | X axis - in position deadband | |
| 0071 | 100 | Y axis - in position deadband | |
| 0072 | 200 | T axis - in position deadband | |
| 0073 | 100 | C axis - in position deadband | |
| 0074 | 500 | X axis - max following error when stopped | |
| 0075 | 500 | Y axis - max following error when stopped | |
| 0076 | 500 | T axis - max following error when stopped | |
| 0077 | 3000 | C axis - max following error when stopped | |
| 0078 | 3000 | X axis - max following error when moving | |
| 0079 | 3000 | Y axis - max following error when moving | |
| 0080 | 12000 | T axis - max following error when moving | |
| 0081 | 20000 | C axis - max following error when moving | |
| 0082 | ----- | X axis grid shift (home position offset) - varies | |
| 0083 | ----- | Y axis grid shift (home position offset) - varies | |
| 0084 | ----- | T axis grid shift (home position offset) - varies | |
| 0085 | ----- | C1 (4th axis) grid shift (home position offset) – varies | |
| 0347 | ----- | C2 (5th axis) grid shift (home position offset) – varies | |
| Note: Offsets measured in detect units. 1 detect unit =.0005 inch. Lower number moves hole closer to edge of sheet - must power down and back up to register change. | |||
| 0086 | 3584 | X axis servo loop gain multiplier | |
| 0087 | 3584 | Y axis servo loop gain multiplier | |
| 0088 | 896 | T axis servo loop gain multiplier | |
| 0089 | 597 | C axis servo loop gain multiplier | |
| 0090 | 0 | gain factor of d/a converter | |
| 0091 | 10 | ||
| 0092-0093 | 0 | ||
| 0094 | 15000 | T axis rapid traverse speed in auto | |
| 0095 | 2160 | C axis feed rate in auto mode (30-15000 counts) | |
| 0096-0097 | 0 | ||
| 0098 | 1100 | T axis accel/decel time constant in auto | |
| 0099 | 0 | ||
| 0100 | 1 | X axis accel/decel time constant in manual | |
| 0101 | 1 | Y axis accel/decel time constant in manual | |
| 0102 | 70 | T axis accel/decel time constant in manual | |
| 0103-0104 | 0 | ||
| 0105 | 200 | accel/decel time constant in contour mode | |
| 0106 | 300 | max feedrate | |
| 0107-0113 | 0 | ||
| 0114 | 500 | slow speed during reference, 500 max. Too slow and axis won’t reference ( 91 alarm) | |
| 0115-0117 | 0 | ||
| 0118 | 0 | C axis backlash amount. | |
| 0119-0123 | 0 | ||
| 0124 | 0 | X axis amount of velos of drift comp. in servo loop | |
| 0125 | 0 | Y axis amount of velos of drift comp. in servo loop | |
| 0126 | 0 | T axis amount of velos of drift comp. in servo loop | |
| 0127 | 3 | C1 (4th axis) amount of velos of drift comp. in servo loop | |
| 0128-0142 | 0 | ||
| 0143 | 1010 | X minus software limit | |
| 0144 | 3371 | Y minus software limit | |
| 0145-0146 | 0 | ||
| 0147 | -49010 | X plus software limit. | |
| 0148 | -39001 | Y plus software limit. | |
| 0149-0166 | 0 | ||
| 0167 | 200 | accel/decel ramp data (inch) | |
| 0168 | 500 | accel/decel ramp data (inch) | |
| 0169 | 1000 | accel/decel ramp data (inch) | |
| 0170 | 3000 | accel/decel ramp data (inch) | |
| 0171 | 5000 | accel/decel ramp data (inch) | |
| 0172 | 10000 | accel/decel ramp data (inch) | |
| 0173-0179 | 0 | ||
| 0180-0299 | not used | ||
| 0300 | 00010010 | bit 1 | = 1 enables G31 |
| 0301 | 00000010 | ||
| 0302 | 00000001 | bit 0 | = 1 micron type auto-index. |
| = 0 old style auto-index. | |||
| 0303 | 00000001 | ||
| 0304 | 00000000 | ||
| 0305 | 01100000 | bit 6 | = 1 param. 444 sets TPF 9. |
| 0306 | 00000010 | bit 1 | = 0 T code on same line with X, Y coordinate (non-auto index machines) |
| = 1 T code on separate line (auto-index machines) | |||
| bit 3 | = 1 M02, M30, M99 not counted as program end (looks for %) | ||
| 0307 | 00001100 | ||
| 0308 | 01000000 | ||
| 0309 | 00001111 | bit 0 | = 1 automatic coordinate system is effective for X axis |
| bit 1 | = 1 automatic coordinate system is effective for Y axis | ||
| bit 2 | = 1 automatic coordinate system is effective for T axis | ||
| bit 3 | = 1 automatic coordinate system is effective for C axis | ||
| 0310 | 00000101 | Characteristics for 0310 to 0313 | |
| 0311 | 00100101 | bit 5 | = 1 DC1 - DC4 codes not used. |
| 0312 | 00000101 | = 0 DC1 - DC4 codes used. | |
| 0313 | 00000101 | bit 4 | = 1 2 stop bits |
| = 0 1 stop bit | |||
| bit 0-3 | set baud rate for 1/0 interface, see parameters 0340 -341 |
Baud |
3 |
2 |
1 |
0 |
50 |
0 |
0 |
0 |
0 |
100 |
0 |
0 |
0 |
1 |
110 |
0 |
0 |
1 |
0 |
150 |
0 |
0 |
1 |
1 |
200 |
0 |
1 |
0 |
0 |
300 |
0 |
1 |
0 |
1 |
600 |
0 |
1 |
1 |
0 |
1200 |
0 |
1 |
1 |
1 |
2400 |
1 |
0 |
0 |
0 |
4800 |
1 |
0 |
0 |
1 |
9600 |
1 |
0 |
1 |
0 |
| 0314-0315 | 00000000 | ||
| 0316 | 00011000 | selects resolver as feedback device for C axis | |
| 0317 | 00001110 | ||
| 0318 | 11100000 | bit 5 | = 1 display of macro contents suppressed while running program |
| = 0 macro contents displayed while running program | |||
| . | bit 6 | = 1 single stepping through macro disabled | |
| = 0 single stepping enabled | |||
| bit 7 | = 1 programs in 9000 series are locked, cannot be loaded or edited | ||
| = 0 programs in 9000 series can be loaded or edited. | |||
| 0319 | 10000001 | bit 7 | same as param. 0318 for 8000 series programs |
| 0320-0322 | 0 | ||
| 0323 | 0 | = 0 separate movement of axes (T moves 1st ) | |
| = 31 G31 in program calls macro 9010 program for simultaneous axis movement with T code on same line as X and Y. T code on separate line still works. | |||
| 0324 | 82 | ||
| 0325 | 83 | ||
| 0326 | 84 | ||
| 0327-0339 | 0 | ||
| 0340 | 2 | Input Device | |
| 0 = tape reader | |||
| 1 = ASR-43 (set baud in param. 310) | |||
| 2 = RS-232 (set baud in param. 311) | |||
| 3 = RS-232 (set baud in param. 312) | |||
| 4 = RS-232 (set baud in param. 313) | |||
| 0341 | 2 | Output Device | |
| 0 = Facit 4070 punch | |||
| 1 = ASR-43 (set baud in param. 310) | |||
| 2 = RS-232 (set baud in param. 311) | |||
| 3 = RS-232 (set baud in param. 312) | |||
| 4 = RS-232 (set baud in param. 313) | |||
| 0342 | 500 | ||
| 0343-0346 | 0 | ||
| 0347 | ----- | C2 (5th axis) grid shift (home position offset) – varies | |
| 0348 | 400 | ||
| 0349-0364 | 0 | ||
| 0365 | 2000 | C1/C2 maximum deviation permitted (setting max is 2200). | |
| 0366 | 1500 | C axis related | |
| 0367-0374 | 0 | ||
| 0375 | 121920 | ||
| 0376 | 96520 | ||
| 0377-0378 | 0 | ||
| 0379 | 48000 | absolute preset at home for X axis | |
| 0380 | 38000 | absolute preset at home for Y axis | |
| 0381-0389 | 0 | ||
| 0390 | ----- | T06 A-1 tool offset – varies | |
| 0391-0393 | 0 | ||
| 0394 | ----- | T16 A-1 tool offset – varies | |
| 0395-0397 | 0 | ||
| 0398 | ----- | T28 A-1 tool offset – varies | |
| 0399-0407 | 0 | ||
| 0408-0419 | not used | ||
| 0420 | 10011100 | ||
| 0421 | 10101001 | bit 0 | = 0 4th axis used for C axis |
| = 1 5th axis used for C axis | |||
| 0422 | 00000000 | C axis servo loop gain multiplier | |
| 0423 | 10000000 | ||
| 0424 | 00000010 | ||
| 0425 | 81 | sets M81 code (post-punch delay on) | |
| 0426 | 82 | sets M82 code (post-punch delay off) | |
| 0427 | 3 | ||
| 0428 | 4 | ||
| 0429 | 12 | M code for nibble start (coordinate nibble) | |
| 0430 | 13 | M code for nibble end (coordinate nibble) | |
| 0431-0435 | 0 | ||
| 0436 | ----- | delay from punch end switch to clutch dump – varies | |
| 0437 | 150 | ||
| 0438 | 100 | delay before punch in milliseconds | |
| 0439 | 100 | M81 post-punch delay time in milliseconds | |
| 0440-0443 | 0 | ||
| 0444 | ----- | delay from clutch dump to brake on – varies | |
| 0445-0451 | 0 | ||
| 0452 | 7000 | X axis position loop gain | |
| 0453 | 5600 | Y axis position loop gain | |
| 0454 | 4000 | T axis position loop gain | |
| 0455 | 3400 | C axis position loop gain | |
| 0456 | 800 | ||
| 0457 | 800 | ||
| 0458 | 6500 | ||
| 0459 | 1200 | rapid traverse rate (table speed in auto) | |
| 0460 | 160 | jog ramp parameters | |
| 0461 | 160 | jog ramp parameters | |
| 0462 | 450 | jog ramp parameters | |
| 0463 | 0 | ||
| 0464 | 3000 | T axis jog feedrate | |
| 0465 | 0 | ||
| 0466 | 1100 | T axis reference speed | |
| 0467 | 50 | C axis low speed rate during reference point return (FL speed) | |
| 0468 | 1300 | max. nibble bite for G68/G69 metric 1-9999 (.01 mm) | |
| 0469 | 510 | max. Nibble bite for G68/G69 inch 1-9999 (.001") | |
| 0470 | 1300 | maximum nibble feedrate (Q) - metric value | |
| 0471 | 510 | maximum nibble feedrate (Q) - inch value | |
| 0472 | 508 | accel/decel ramp data (metric) | |
| 0473 | 1270 | accel/decel ramp data (metric) | |
| 0474 | 2540 | accel/decel ramp data (metric) | |
| 0475 | 7620 | accel/decel ramp data (metric) | |
| 0476 | 12700 | accel/decel ramp data (metric) | |
| 0477 | 25400 | accel/decel ramp data (metric) | |
| 0478-0483 | 3000 | rapid traverse speeds X axis | |
| 0484 | 3200 | rapid traverse speed | |
| 0485 | 40 | 0 - .2 inch ramp | |
| 0486 | 135 | .2 - .5 inch ramp | |
| 0487 | 135 | .5 - 1 inch ramp | |
| 0488 | 175 | 1 - 3 inch ramp | |
| 0489 | 180 | 3 - 5 inch ramp | |
| 0490 | 200 | 5 - 10 inch ramp | |
| 0491 | 390 | 10+ inch ramp | |
| 0492-0497 | 3000 | rapid traverse speeds Y axis | |
| 0498 | 3200 | rapid traverse speed | |
| 0499 | 40 | 0 - .2 inch ramp | |
| 0500 | 155 | .2 - .5 inch ramp | |
| 0501 | 165 | .5 - 1 inch ramp | |
| 0502 | 175 | 1 - 3 inch ramp | |
| 0503 | 180 | 3 - 5 inch ramp | |
| 0504 | 200 | 5 - 10 inch ramp | |
| 0505 | 390 | 10+ inch ramp | |
| 0506 | 127 | ||
| 0507 | 50 | 10 = .010 inch, sets back-out of work clamps during prog. move will accept max. of 4.0 inches. Only active with G75, not 03/M04. | |
| 0508-0509 | 0 | ||
| 0510-0515 | 35 | X axis punch anticipation | |
| 0516 | 0 | ||
| 0517-0523 | 35 | Y axis punch anticipation | |
| 0524-0539 | 0 | ||
| 0540 | 1 | T axis tool station at home | |
| 0541 | 33 | number of turret stations | |
| 0542 | 1 | T command for station 1 | |
| 0543 | 2 | T command for station 2 | |
| 0544 to | 3 to | T command for station 3 to | |
| 0574 | 33 | T command for station 33 | |
| 0575-0599 | 0 | ||
| 0600-0767 | 0 | ||
| 0768-0771 | 1250 | 1.5" station tool offsets | |
| 0772 | 0 | ||
| 0773-0776 | 1250 | 1.5" station tool offsets | |
| 0777 | 0 | ||
| 0778-0781 | 1250 | 1.5" station tool offsets | |
| 0782 | 0 | ||
| 0783-0787 | 1250 | 1.5" station tool offsets | |
| 0788 | 0 | ||
| 0789-0793 | 1250 | 1.5" station tool offsets | |
| 0794 | 0 | ||
| 0795-0799 | 1250 | 1.5" station tool offsets | |
| 0800-0842 | 0 | ||
| 0843 | 25600 | positioning counts for T02 | |
| 0844 | 3840 | positioning counts for T03 | |
| 0845 | 51200 | positioning counts for T04 | |
| 0846 | 64000 | positioning counts for T05 | |
| 0847 | 89600 | positioning counts for T06 | |
| 0848 | 115200 | positioning counts for T07 | |
| 0849 | 128000 | positioning counts for T08 | |
| 0850 | 140800 | positioning counts for T09 | |
| 0851 | 153600 | positioning counts for T10 | |
| 0852 | 179200 | positioning counts for T11 | |
| 0853 | 204800 | positioning counts for T12 | |
| 0854 | 217600 | positioning counts for T13 | |
| 0855 | 230400 | positioning counts for T14 | |
| 0656 | 243200 | positioning counts for T15 | |
| 0857 | 268800 | positioning counts for T16 | |
| 0858 | 294400 | positioning counts for T17 | |
| 0859 | 307200 | positioning counts for T18 | |
| 0860 | 320000 | positioning counts for T19 | |
| 0861 | 332000 | positioning counts for T20 | |
| 0862 | 345600 | positioning counts for T21 | |
| 0863 | 371200 | positioning counts for T22 | |
| 0864 | 396600 | positioning counts for T23 | |
| 0865 | 409600 | positioning counts for T24 | |
| 0866 | 422400 | positioning counts for T25 | |
| 0867 | 435200 | positioning counts for T26 | |
| 0868 | 448000 | positioning counts for T27 | |
| 0869 | 473600 | positioning counts for T28 | |
| 0870 | 499200 | positioning counts for T29 | |
| 0871 | 512000 | positioning counts for T30 | |
| 0872 | 524800 | positioning counts for T31 | |
| 0873 | 537600 | positioning counts for T32 | |
| 0874 | 550400 | positioning counts for T33 | |
| 0875-0916 | 0 | ||
| 0917-0949 | ----- | counter for hits on each tool (0917=T01, 0918 = T02, etc.) – varies | |
| 0950-0991 | 0 | ||
| 0992 | 576000 | encoder counts for turret revolution | |
| 0993 | 0 | ||
| 0994 | 2 | C2 (5th axis) amount of velos of drift comp. in servo loop | |
| 0995 | 1500 | C axis maximum feedrate in nibble mode (1-9999, 1 unit =.01 degree). | |
| 0996 | 0 | ||
| 0997 and up | not used |